If you are planning to study Animal Science and Technology at Abia State University located in Abia State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABSU.
Does Abia State University (ABSU) offer Animal Science and Technology?
No, Abia State University does not offer Animal Science and Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Abia State University (ABSU) below to check if the Animal Science and Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Animal Science and Technology When Accredited in Abia State University (ABSU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Animal Science and Technology department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agric Science and
JAMB Subject Combination
Biology / Agriculture and
ABSU Cut-Off Mark for Animal Science and Technology
The general UTME cut-off mark is 180, but due to the variation of Animal Science and Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABSU Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Medical Laboratory Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Medical Laboratory Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Crop Production and Protection
SSCE Requirements
To study this course, candidates aspiring to gain admission into Crop Production and Protection department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Environmental Science
SSCE Requirements
To study this course, candidates seeking admission into the Environmental Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
For holders of NTC, the relevant subjects could be;
General Wood work, Building / Engineering, Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Computer Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Nigerian Tertiary Institutions Offering Animal Science and Technology Course