If you are planning to study Automobile Technology Education at Abia State University located in Abia State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABSU.
Does Abia State University (ABSU) offer Automobile Technology Education?
No, Abia State University does not offer Automobile Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Abia State University (ABSU) below to check if the Automobile Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Automobile Technology Education When Accredited in Abia State University (ABSU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Automobile Technology Education department under Faculty of Education.
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
ABSU Cut-Off Mark for Automobile Technology Education
The general UTME cut-off mark is 180, but due to the variation of Automobile Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABSU Science Courses with their Requirements
Zoology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Zoology department.
two (2) other Science subject.
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Physiology
SSCE Requirements
To study this course, candidates seeking admission into the Physiology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Education and Chemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Education and Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology and Agricultural Science.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Microbiology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology department.
Environmental Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
For holders of NTC, the relevant subjects could be;
General Wood work, Building / Engineering, Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Nigerian Tertiary Institutions Offering Automobile Technology Education Course