If you are planning to study Forestry and Wood Technology at Abia State University located in Abia State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABSU.
Does Abia State University (ABSU) offer Forestry and Wood Technology?
No, Abia State University does not offer Forestry and Wood Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Abia State University (ABSU) below to check if the Forestry and Wood Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Forestry and Wood Technology When Accredited in Abia State University (ABSU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Forestry and Wood Technology department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Mathematics / Physics and
Biology / Agricultural Science.
ABSU Cut-Off Mark for Forestry and Wood Technology
The general UTME cut-off mark is 180, but due to the variation of Forestry and Wood Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABSU Science Courses with their Requirements
Pure and Industrial Physics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Pure and Industrial Physics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) other Science subject from:
Biology or Agricultural Science.
Geography
SSCE Requirements
To study this course, candidates aspiring to gain admission into Geography department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other two (2) Science subjects.
Environmental Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
For holders of NTC, the relevant subjects could be;
General Wood work, Building / Engineering, Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Civil Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Education and Biology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Biology department.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Forestry and Wood Technology Course