If you are planning to study Information and Communication Technology (ICT) at Abia State University located in Abia State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABSU.
Does Abia State University (ABSU) offer Information and Communication Technology?
No, Abia State University does not offer Information and Communication Technology under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Abia State University (ABSU) below to check if the Information and Communication Technology course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Information and Communication Technology (ICT) When Accredited in Abia State University (ABSU)
O’Level Requirements
To study this course, candidates seeking admission into the Information and Communication Technology (ICT) department under Faculty of Data and Decision Sciences, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
JAMB Subject Combination
Biology, Chemistry, Agric Science,
ABSU Cut-Off Mark for Information and Communication Technology (ICT)
The general UTME cut-off mark is 180, but due to the variation of Information and Communication Technology (ICT) cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABSU Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Mechanical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
Physiology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physiology department.
Zoology
SSCE Requirements
To study this course, candidates seeking admission into the Zoology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subject.
Mathematics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Chemistry and Industrial Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemistry and Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Environmental Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
For holders of NTC, the relevant subjects could be;
General Wood work, Building / Engineering, Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Nigerian Universities Offering Information and Communication Technology Course