If you are planning to study Polymer Technology at Abubakar Tatari Ali Polytechnic located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ATAP.
Does Abubakar Tatari Ali Polytechnic (ATAP) offer Polymer Technology?
No, Abubakar Tatari Ali Polytechnic does not offer Polymer Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tatari Ali Polytechnic (ATAP) below to check if the Polymer Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Polymer Technology When Accredited in Abubakar Tatari Ali Polytechnic (ATAP)
O’Level Requirements
To study this course, candidates seeking admission into the Polymer Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
ATAP Cut-Off Mark for Polymer Technology
The general UTME cut-off mark is 180, but due to the variation of Polymer Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATAP Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATAP Science Courses with their Requirements
Geological Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Geological Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) subjects from:
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Fisheries Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Fisheries Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
any other Science subject.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Architectural Technology
SSCE Requirements
To study this course, candidates seeking admission into the Architectural Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Nigerian Tertiary Institutions Offering Polymer Technology Course