If you are planning to study Surveying and Geoinformatics at Abubakar Tatari Ali Polytechnic located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ATAP.
Does Abubakar Tatari Ali Polytechnic (ATAP) offer Surveying and Geoinformatics?
No, Abubakar Tatari Ali Polytechnic does not offer Surveying and Geoinformatics under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tatari Ali Polytechnic (ATAP) below to check if the Surveying and Geoinformatics course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Surveying and Geoinformatics When Accredited in Abubakar Tatari Ali Polytechnic (ATAP)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
JAMB Subject Combination
Chemistry, Geography, Art, Biology and Economics.
ATAP Cut-Off Mark for Surveying and Geoinformatics
The general UTME cut-off mark is 180, but due to the variation of Surveying and Geoinformatics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATAP Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATAP Science Courses with their Requirements
Fisheries Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Fisheries Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
any other Science subject.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Forestry Technology
SSCE Requirements
To study this course, candidates seeking admission into the Forestry Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Geological Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Geological Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) subjects from:
Animal Health and Production Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Animal Health and Production Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three (3) of the following:
Geography, Food and Nutrition, Economics, Technical Drawing,
English Language, Physics, Chemistry, Nigerian Language, and Home Economics.
Nigerian Polytechnics Offering Surveying and Geoinformatics Course