If you are planning to study Petroleum and Gas Processing at Adamawa State Polytechnic, Yola located in Adamawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ADAMAWAPOLY.
Does Adamawa State Polytechnic, Yola (ADAMAWAPOLY) offer Petroleum and Gas Processing?
No, Adamawa State Polytechnic, Yola does not offer Petroleum and Gas Processing under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Adamawa State Polytechnic, Yola (ADAMAWAPOLY) below to check if the Petroleum and Gas Processing course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Petroleum and Gas Processing When Accredited in Adamawa State Polytechnic, Yola (ADAMAWAPOLY)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Petroleum and Gas Processing department under Faculty of Engineering / Technology.
any two (2) relevant subjects from:
Biology/Agricultural Science, Technical Drawing,
Basic Electronics/Basic Electricity, Auto Mechanics,
Metal Work, Woodwork for Civil Engineering Technology,
Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering 'O' Level pass in Biology is required.
JAMB Subject Combination
Chemistry or Technical Drawing.
ADAMAWAPOLY Cut-Off Mark for Petroleum and Gas Processing
The general UTME cut-off mark is 180, but due to the variation of Petroleum and Gas Processing cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ADAMAWAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ADAMAWAPOLY Science Courses with their Requirements
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Civil Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering Technology department.
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Nigerian Tertiary Institutions Offering Petroleum and Gas Processing Course