If you are planning to study Dental Technology at Ahmadu Bello University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABU.
Does Ahmadu Bello University (ABU) offer Dental Technology?
No, Ahmadu Bello University does not offer Dental Technology under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Ahmadu Bello University (ABU) below to check if the Dental Technology course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Dental Technology When Accredited in Ahmadu Bello University (ABU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Dental Technology department under Faculty of Health and Medical Sciences.
JAMB Subject Combination
one (1) other Science subject.
ABU Cut-Off Mark for Dental Technology
The general UTME cut-off mark is 230, but due to the variation of Dental Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABU Science Courses with their Requirements
Human Kinetics
SSCE Requirements
To study this course, candidates seeking admission into the Human Kinetics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Health Science / Physical Education / Biology
Any other two (2) relevant subjects
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Biological Science
SSCE Requirements
To study this course, candidates seeking admission into the Biological Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any other relevant Science subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Metallurgical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Metallurgical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Mechanical Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Dental Technology Course