If you are planning to study Metallurgical and Material Engineering at Akwa Ibom State Polytechnic located in Akwa Ibom State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into AKWAIBOMPOLY.
Does Akwa Ibom State Polytechnic (AKWAIBOMPOLY) offer Metallurgical and Material Engineering?
No, Akwa Ibom State Polytechnic does not offer Metallurgical and Material Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Akwa Ibom State Polytechnic (AKWAIBOMPOLY) below to check if the Metallurgical and Material Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical and Material Engineering When Accredited in Akwa Ibom State Polytechnic (AKWAIBOMPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metallurgical and Material Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one other Science subject.
AKWAIBOMPOLY Cut-Off Mark for Metallurgical and Material Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical and Material Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from AKWAIBOMPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other AKWAIBOMPOLY Science Courses with their Requirements
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Statistics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architectural Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architectural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Nigerian Tertiary Institutions Offering Metallurgical and Material Engineering Course