If you are planning to study Glass Technology at Alex Ekwueme Federal University Ndufu Alike-Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into AE-FUNAI.
Does Alex Ekwueme Federal University Ndufu Alike-Ikwo (AE-FUNAI) offer Glass Technology?
No, Alex Ekwueme Federal University Ndufu Alike-Ikwo does not offer Glass Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Alex Ekwueme Federal University Ndufu Alike-Ikwo (AE-FUNAI) below to check if the Glass Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Glass Technology When Accredited in Alex Ekwueme Federal University Ndufu Alike-Ikwo (AE-FUNAI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Glass Technology department under Faculty of Engineering / Technology.
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
AE-FUNAI Cut-Off Mark for Glass Technology
The general UTME cut-off mark is 180, but due to the variation of Glass Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from AE-FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other AE-FUNAI Science Courses with their Requirements
Education and Physics
SSCE Requirements
To study this course, candidates seeking admission into the Education and Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects or NTC / NBC.
Education and Chemistry
SSCE Requirements
To study this course, candidates seeking admission into the Education and Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology and Agricultural Science.
Physiology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physiology department.
Applied Geophysics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Applied Geophysics department.
Biology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics / Physics and
any one other relevant subject.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Glass Technology Course