If you are planning to study Mechanical and Metallurgical Engineering at Alex Ekwueme Federal University Ndufu Alike-Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into AE-FUNAI.
Does Alex Ekwueme Federal University Ndufu Alike-Ikwo (AE-FUNAI) offer Mechanical and Metallurgical Engineering?
No, Alex Ekwueme Federal University Ndufu Alike-Ikwo does not offer Mechanical and Metallurgical Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Alex Ekwueme Federal University Ndufu Alike-Ikwo (AE-FUNAI) below to check if the Mechanical and Metallurgical Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical and Metallurgical Engineering When Accredited in Alex Ekwueme Federal University Ndufu Alike-Ikwo (AE-FUNAI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical and Metallurgical Engineering department under Faculty of Engineering / Technology.
one (1) other Science subject.
AE-FUNAI Cut-Off Mark for Mechanical and Metallurgical Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechanical and Metallurgical Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from AE-FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other AE-FUNAI Science Courses with their Requirements
Anatomy
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Anatomy department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Medicine and Surgery
SSCE Requirements
To study this course, candidates aspiring to gain admission into Medicine and Surgery department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fisheries and Aquaculture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Fisheries and Aquaculture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science,
Physics/Geography/Economics.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Geology and Geophysics
SSCE Requirements
To study this course, candidates seeking admission into the Geology and Geophysics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Geology department.
any other relevant subject.
Physical and Health Education
SSCE Requirements
To study this course, candidates seeking admission into the Physical and Health Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology or its equivalent
and any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Mechanical and Metallurgical Engineering Course