
If you are planning to study Foundry Engineering Technology at Auchi Polytechnic located in Edo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into AUCHIPOLY.
Does Auchi Polytechnic (AUCHIPOLY) offer Foundry Engineering Technology?
No, Auchi Polytechnic does not offer Foundry Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Auchi Polytechnic (AUCHIPOLY) below to check if the Foundry Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Foundry Engineering Technology When Accredited in Auchi Polytechnic (AUCHIPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Foundry Engineering Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
JAMB Subject Combination
Physics or Technical Drawing.
AUCHIPOLY Cut-Off Mark for Foundry Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Foundry Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from AUCHIPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other AUCHIPOLY Science Courses with their Requirements
Polymer Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Polymer Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Food Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Food Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
any two of the following:
Geography, Food and Nutrition, Economics, Technical Drawing, Physics, Chemistry, Nigerian Language and Home Economics.
At least a pass in Chemistry is required.
Mineral and Petroleum Resources Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mineral and Petroleum Resources Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Woodwork for Civil Engineering Technology, Further Mathematics, English Language, Geography, Economics/Commerce,
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work.
Estate Management and Valuation
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Estate Management and Valuation department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Glass / Ceramics Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Glass / Ceramics Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Nigerian Polytechnics Offering Foundry Engineering Technology Course