If you are planning to study Welding and Fabrication Technology at Auchi Polytechnic located in Edo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into AUCHIPOLY.
Does Auchi Polytechnic (AUCHIPOLY) offer Welding and Fabrication Technology?
No, Auchi Polytechnic does not offer Welding and Fabrication Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Auchi Polytechnic (AUCHIPOLY) below to check if the Welding and Fabrication Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Welding and Fabrication Technology When Accredited in Auchi Polytechnic (AUCHIPOLY)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Welding and Fabrication Technology department under Faculty of Engineering / Technology.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
JAMB Subject Combination
Physics/Technical Drawing or Chemistry.
AUCHIPOLY Cut-Off Mark for Welding and Fabrication Technology
The general UTME cut-off mark is 180, but due to the variation of Welding and Fabrication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from AUCHIPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other AUCHIPOLY Science Courses with their Requirements
Mechanical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Agricultural Engineering / Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering / Technology department.
any three of the following:
Biology / Agricultural Science, Chemistry, Technical Drawing, Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology / Agricultural Science / Food and Nutrition.
Glass / Ceramics Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Glass / Ceramics Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Architectural Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architectural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Nigerian Polytechnics Offering Welding and Fabrication Technology Course