If you are planning to study Community Health at Bells University of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Bells University.
Does Bells University of Technology (BUT) offer Community Health?
No, Bells University of Technology does not offer Community Health under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Bells University of Technology (BUT) below to check if the Community Health course under the Faculty of Health and Medical Sciences has been updated.
O’Level Requirements
To study this course, candidates aspiring to gain admission into Community Health department under Faculty of Health and Medical Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Health Science and
Nutrition, Chemistry, Physics,
Religious Studies, Geography,
Economics, Nigerian Language and
at least a pass in English Language, Food and Nutrition/Home Management.
Bells University Cut-Off Mark for Community Health
The general UTME cut-off mark is 230, but due to the variation of Community Health cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Bells University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Bells University Science Courses with their Requirements
Communication Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Communication Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Telecommunication Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Telecommunication Engineering department.
any two (2) other relevant subjects.
Biomedical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biomedical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Food Science and Technology (FT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.