If you are planning to study Explosives Ordinance Technology at Benue State Polytechnic located in Benue State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into BENPOLY.
Does Benue State Polytechnic (BENPOLY) offer Explosives Ordinance Technology?
No, Benue State Polytechnic does not offer Explosives Ordinance Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Benue State Polytechnic (BENPOLY) below to check if the Explosives Ordinance Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Explosives Ordinance Technology When Accredited in Benue State Polytechnic (BENPOLY)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Explosives Ordinance Technology department under Faculty of Engineering / Technology.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics English Language and Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety and Environmental Engineering: a pass in Biology is required At least a credit pass in English Language is required.
JAMB Subject Combination
Chemistry/Technical Drawing,
BENPOLY Cut-Off Mark for Explosives Ordinance Technology
The general UTME cut-off mark is 180, but due to the variation of Explosives Ordinance Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from BENPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other BENPOLY Science Courses with their Requirements
Foundry Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Foundry Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Metallurgical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Metallurgical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Printing Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Printing Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Civil Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering Technology department.
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Explosives Ordinance Technology Course