If you are planning to study Forestry and Wildlife at Benue State Polytechnic located in Benue State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into BENPOLY.
Does Benue State Polytechnic (BENPOLY) offer Forestry and Wildlife?
No, Benue State Polytechnic does not offer Forestry and Wildlife under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Benue State Polytechnic (BENPOLY) below to check if the Forestry and Wildlife course under the Faculty of Agriculture has been updated.
Admission Requirements for Forestry and Wildlife When Accredited in Benue State Polytechnic (BENPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Forestry and Wildlife department under Faculty of Agriculture, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Further Mathematics and Statistics.
JAMB Subject Combination
Biology / Agriculture and
BENPOLY Cut-Off Mark for Forestry and Wildlife
The general UTME cut-off mark is 180, but due to the variation of Forestry and Wildlife cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from BENPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other BENPOLY Science Courses with their Requirements
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Foundry Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Foundry Engineering Technology department.
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronic Engineering Technology department.
any other Science Subject.
Civil Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Printing Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Printing Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Nigerian Tertiary Institutions Offering Forestry and Wildlife Course