If you are planning to study Auto and Mechanical Technology Education at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Auto and Mechanical Technology Education?
No, Covenant University, Ota does not offer Auto and Mechanical Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Auto and Mechanical Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Auto and Mechanical Technology Education When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Auto and Mechanical Technology Education department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one (1) of Biology / Agricultural Science; Physics, or Chemistry,
Auto Technical, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition,
Physical and Health Education, General Science / Integrated Science, Building, Electrical Electronic, Metal Work and Wood Work.
Covenant University Cut-Off Mark for Auto and Mechanical Technology Education
The general UTME cut-off mark is 180, but due to the variation of Auto and Mechanical Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
Industrial Mathematics
SSCE Requirements
To study this course, candidates seeking admission into the Industrial Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Computer Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Electrical / Electronics Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Chemical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Chemical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Industrial Physics With Electronics and IT Application
SSCE Requirements
To study this course, candidates aspiring to gain admission into Industrial Physics With Electronics and IT Application department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics and one (1) other Science.
Nigerian Tertiary Institutions Offering Auto and Mechanical Technology Education Course