If you are planning to study Fisheries and Wildlife Management at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Fisheries and Wildlife Management?
No, Covenant University, Ota does not offer Fisheries and Wildlife Management under its Faculty of Renewable and Natural Resources. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Fisheries and Wildlife Management course under the Faculty of Renewable and Natural Resources has been updated.
Admission Requirements for Fisheries and Wildlife Management When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Fisheries and Wildlife Management department under Faculty of Renewable and Natural Resources, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
Physics / Geography / Economics.
JAMB Subject Combination
Biology / Agricultural Science.
Covenant University Cut-Off Mark for Fisheries and Wildlife Management
The general UTME cut-off mark is 180, but due to the variation of Fisheries and Wildlife Management cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Industrial Physics With Applied Geophysics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Physics With Applied Geophysics department.
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Chemical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Chemical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Computer Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Engineering department.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Fisheries and Wildlife Management Course