If you are planning to study Health and Safety Education at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Health and Safety Education?
No, Covenant University, Ota does not offer Health and Safety Education under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Health and Safety Education course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Health and Safety Education When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Health and Safety Education department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any three (3) Science Subjects from:
JAMB Subject Combination
any two (2) Arts subjects.
Covenant University Cut-Off Mark for Health and Safety Education
The general UTME cut-off mark is 230, but due to the variation of Health and Safety Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Industrial Physics With Electronics and IT Application
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Physics With Electronics and IT Application department.
Mathematics and one (1) other Science.
Information and Communication Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Information and Communication Engineering department.
any two (2) other relevant subjects.
Computer Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Industrial Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects.
Biology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biology department.
Mathematics / Physics and
any one other relevant subject.
Nigerian Tertiary Institutions Offering Health and Safety Education Course