If you are planning to study Remote Sensing and Geosciences Information System at Covenant University, Ota located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Covenant University.
Does Covenant University, Ota (CU) offer Remote Sensing and Geosciences Information System?
No, Covenant University, Ota does not offer Remote Sensing and Geosciences Information System under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at Covenant University, Ota (CU) below to check if the Remote Sensing and Geosciences Information System course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Remote Sensing and Geosciences Information System When Accredited in Covenant University, Ota (CU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Remote Sensing and Geosciences Information System department under Faculty of Earth and Mineral Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Joinery,
Floors and Ceiling Finishing, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
JAMB Subject Combination
Art, Biology and Economics.
Covenant University Cut-Off Mark for Remote Sensing and Geosciences Information System
The general UTME cut-off mark is 180, but due to the variation of Remote Sensing and Geosciences Information System cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Covenant University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Covenant University Science Courses with their Requirements
Industrial Chemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Industrial Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science.
Petroleum Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Petroleum Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Industrial Mathematics
SSCE Requirements
To study this course, candidates seeking admission into the Industrial Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
Chemical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Chemical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Information and Communication Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Information and Communication Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Remote Sensing and Geosciences Information System Course