If you are planning to study Ceramics Technology at Crown Polytechnic, Ado-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Crown Polytechnic.
Does Crown Polytechnic, Ado-Ekiti offer Ceramics Technology?
No, Crown Polytechnic, Ado-Ekiti does not offer Ceramics Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Crown Polytechnic, Ado-Ekiti below to check if the Ceramics Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Ceramics Technology When Accredited in Crown Polytechnic, Ado-Ekiti
O’Level Requirements
To study this course, candidates aspiring to gain admission into Ceramics Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Crown Polytechnic Cut-Off Mark for Ceramics Technology
The general UTME cut-off mark is 180, but due to the variation of Ceramics Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Crown Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Crown Polytechnic Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Computer Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Engineering department.
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Architectural Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architectural Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Nigerian Tertiary Institutions Offering Ceramics Technology Course