If you are planning to study Orthopaedic and Plaster Technology at Crown Polytechnic, Ado-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Crown Polytechnic.
Does Crown Polytechnic, Ado-Ekiti offer Orthopaedic and Plaster Technology?
No, Crown Polytechnic, Ado-Ekiti does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Crown Polytechnic, Ado-Ekiti below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Crown Polytechnic, Ado-Ekiti
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences.
Crown Polytechnic Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Crown Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Crown Polytechnic Science Courses with their Requirements
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Estate Management and Valuation
SSCE Requirements
To study this course, candidates seeking admission into the Estate Management and Valuation department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Fisheries Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fisheries Technology department.
Biology / Agricultural Science,
any other Science subject.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronic Engineering Technology department.
any other Science Subject.
Computer Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course