If you are planning to study Foundry Engineering Technology at Delta State Polytechnic, Otefe Oghara located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Delta State Polytechnic.
Does Delta State Polytechnic, Otefe Oghara offer Foundry Engineering Technology?
No, Delta State Polytechnic, Otefe Oghara does not offer Foundry Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Delta State Polytechnic, Otefe Oghara below to check if the Foundry Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Foundry Engineering Technology When Accredited in Delta State Polytechnic, Otefe Oghara
O’Level Requirements
To study this course, candidates seeking admission into the Foundry Engineering Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
JAMB Subject Combination
Physics or Technical Drawing.
Delta State Polytechnic Cut-Off Mark for Foundry Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Foundry Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Delta State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Delta State Polytechnic Science Courses with their Requirements
Computer Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Statistics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Industrial Maintenance Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Maintenance Engineering Technology department.
any one (1) of Biology/Agricultural Science.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates seeking admission into the Welding and Fabrication Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Polytechnics Offering Foundry Engineering Technology Course