If you are planning to study Health Information Management at Delta State Polytechnic, Otefe Oghara located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Delta State Polytechnic.
Does Delta State Polytechnic, Otefe Oghara offer Health Information Management?
No, Delta State Polytechnic, Otefe Oghara does not offer Health Information Management under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Delta State Polytechnic, Otefe Oghara below to check if the Health Information Management course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Health Information Management When Accredited in Delta State Polytechnic, Otefe Oghara
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Health Information Management department under Faculty of Health and Medical Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Chemistry, Physics, Geography,
Economics, Religious Knowledge and Nigerian Language.
Delta State Polytechnic Cut-Off Mark for Health Information Management
The general UTME cut-off mark is 230, but due to the variation of Health Information Management cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Delta State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Delta State Polytechnic Science Courses with their Requirements
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Industrial Maintenance Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Maintenance Engineering Technology department.
any one (1) of Biology/Agricultural Science.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Statistics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates seeking admission into the Welding and Fabrication Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Health Information Management Course