If you are planning to study Surveying and Geoinformatics at Delta State Polytechnic, Otefe Oghara located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Delta State Polytechnic.
Does Delta State Polytechnic, Otefe Oghara offer Surveying and Geoinformatics?
No, Delta State Polytechnic, Otefe Oghara does not offer Surveying and Geoinformatics under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Delta State Polytechnic, Otefe Oghara below to check if the Surveying and Geoinformatics course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Surveying and Geoinformatics When Accredited in Delta State Polytechnic, Otefe Oghara
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
JAMB Subject Combination
Chemistry, Geography, Art, Biology and Economics.
Delta State Polytechnic Cut-Off Mark for Surveying and Geoinformatics
The general UTME cut-off mark is 180, but due to the variation of Surveying and Geoinformatics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Delta State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Delta State Polytechnic Science Courses with their Requirements
Industrial Maintenance Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Industrial Maintenance Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one (1) of Biology/Agricultural Science.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Welding and Fabrication Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Welding and Fabrication Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Polytechnics Offering Surveying and Geoinformatics Course