If you are planning to study Orthopaedic and Plaster Technology at Delta State Polytechnic, Ugwashi-Uku located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Delta State Polytechnic.
Does Delta State Polytechnic, Ugwashi-Uku offer Orthopaedic and Plaster Technology?
No, Delta State Polytechnic, Ugwashi-Uku does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Delta State Polytechnic, Ugwashi-Uku below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Delta State Polytechnic, Ugwashi-Uku
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Delta State Polytechnic Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Delta State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Delta State Polytechnic Science Courses with their Requirements
Agricultural and Bio-Environmental Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural and Bio-Environmental Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three of the following:
Biology/Agricultural Science, Chemistry, Technical Drawing Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology/Agricultural Science/Food
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates seeking admission into the Welding and Fabrication Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Agricultural Engineering / Technology
SSCE Requirements
To study this course, candidates seeking admission into the Agricultural Engineering / Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any three of the following:
Biology / Agricultural Science, Chemistry, Technical Drawing, Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology / Agricultural Science / Food and Nutrition.
Foundry Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Foundry Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course