If you are planning to study Plant Physiology and Crop Production at Enugu State University of Science & Technology located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ESUT.
Does Enugu State University of Science & Technology (ESUT) offer Plant Physiology and Crop Production?
No, Enugu State University of Science & Technology does not offer Plant Physiology and Crop Production under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Enugu State University of Science & Technology (ESUT) below to check if the Plant Physiology and Crop Production course under the Faculty of Agriculture has been updated.
Admission Requirements for Plant Physiology and Crop Production When Accredited in Enugu State University of Science & Technology (ESUT)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Plant Physiology and Crop Production department under Faculty of Agriculture, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Biology / Agriculture and
ESUT Cut-Off Mark for Plant Physiology and Crop Production
The general UTME cut-off mark is 180, but due to the variation of Plant Physiology and Crop Production cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ESUT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ESUT Science Courses with their Requirements
Education and Physics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Physics department.
two (2) other Science subjects or NTC / NBC.
Physical and Health Education
SSCE Requirements
To study this course, candidates seeking admission into the Physical and Health Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology or its equivalent
and any two (2) other relevant subjects.
Land Surveying
SSCE Requirements
To study this course, candidates aspiring to gain admission into Land Surveying department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing.
Medicine and Surgery
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medicine and Surgery department.
Applied Biochemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Applied Biochemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Electrical / Electronics Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Building
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Plant Physiology and Crop Production Course