If you are planning to study Orthopaedic and Plaster Technology at Federal Polytechnic, Bauchi located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Federal Polytechnic Bauchi.
Does Federal Polytechnic, Bauchi offer Orthopaedic and Plaster Technology?
No, Federal Polytechnic, Bauchi does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Federal Polytechnic, Bauchi below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Federal Polytechnic, Bauchi
O’Level Requirements
To study this course, candidates seeking admission into the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Federal Polytechnic Bauchi Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Federal Polytechnic Bauchi Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Federal Polytechnic Bauchi Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Architectural Technology
SSCE Requirements
To study this course, candidates seeking admission into the Architectural Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Agricultural and Bio-Environmental Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural and Bio-Environmental Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three of the following:
Biology/Agricultural Science, Chemistry, Technical Drawing Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology/Agricultural Science/Food
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Civil Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Civil Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course