If you are planning to study Geological Technology at Federal Polytechnic, Idah located in Kogi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IDAHPOLY.
Does Federal Polytechnic, Idah (IDAHPOLY) offer Geological Technology?
No, Federal Polytechnic, Idah does not offer Geological Technology under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at Federal Polytechnic, Idah (IDAHPOLY) below to check if the Geological Technology course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Geological Technology When Accredited in Federal Polytechnic, Idah (IDAHPOLY)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Geological Technology department under Faculty of Earth and Mineral Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) subjects from:
IDAHPOLY Cut-Off Mark for Geological Technology
The general UTME cut-off mark is 180, but due to the variation of Geological Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IDAHPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IDAHPOLY Science Courses with their Requirements
Estate Management and Valuation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Estate Management and Valuation department.
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architectural Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architectural Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Foundry Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Foundry Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Geological Technology Course