If you are planning to study Urban and Regional Planning (URP) at Federal Polytechnic, Idah located in Kogi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IDAHPOLY.
Does Federal Polytechnic, Idah (IDAHPOLY) offer Urban and Regional Planning?
No, Federal Polytechnic, Idah does not offer Urban and Regional Planning under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at Federal Polytechnic, Idah (IDAHPOLY) below to check if the Urban and Regional Planning course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Urban and Regional Planning (URP) When Accredited in Federal Polytechnic, Idah (IDAHPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department under Faculty of Earth and Mineral Sciences, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
JAMB Subject Combination
Economics, Physics and Chemistry.
IDAHPOLY Cut-Off Mark for Urban and Regional Planning (URP)
The general UTME cut-off mark is 180, but due to the variation of Urban and Regional Planning (URP) cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IDAHPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IDAHPOLY Science Courses with their Requirements
Metallurgical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Metallurgical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Civil Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Estate Management and Valuation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Estate Management and Valuation department.
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Foundry Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Foundry Engineering Technology department.
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Mechanical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Polytechnics Offering Urban and Regional Planning Course