If you are planning to study Glass Technology at Federal University, Birnin Kebbi located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUBK.
Does Federal University, Birnin Kebbi (FUBK) offer Glass Technology?
No, Federal University, Birnin Kebbi does not offer Glass Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University, Birnin Kebbi (FUBK) below to check if the Glass Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Glass Technology When Accredited in Federal University, Birnin Kebbi (FUBK)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Glass Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
FUBK Cut-Off Mark for Glass Technology
The general UTME cut-off mark is 180, but due to the variation of Glass Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUBK Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUBK Science Courses with their Requirements
Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Medicine and Surgery
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Medicine and Surgery department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Mathematics / Physics and
any one other relevant subject.
Geography
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Geography department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other two (2) Science subjects.
Anatomy
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Anatomy department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Glass Technology Course