If you are planning to study Fine and Applied Arts at Federal University Ndufu Alike, Ikwo located in Ebonyi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUNAI.
Does Federal University Ndufu Alike, Ikwo (FUNAI) offer Fine and Applied Arts?
No, Federal University Ndufu Alike, Ikwo does not offer Fine and Applied Arts under its Faculty of Arts and Humanities. However, since our course list is updated regularly, you can visit the courses available at Federal University Ndufu Alike, Ikwo (FUNAI) below to check if the Fine and Applied Arts course under the Faculty of Arts and Humanities has been updated.
Admission Requirements for Fine and Applied Arts When Accredited in Federal University Ndufu Alike, Ikwo (FUNAI)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Fine and Applied Arts department under Faculty of Arts and Humanities, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mathematics, Fine Arts and
two (2) other relevant subjects.
For NTC the other two (2) relevant subjects could be from any of the following:
Graphic Painting, Ceramics, Basic Electricity, Building/Engineering/Environmental/Technology Drawing,
Decorative Painting, Spray Painting, Lining, Sign and Design, Wall Handling, Colour Mixing/Matching and Glazing.
FUNAI Cut-Off Mark for Fine and Applied Arts
The general UTME cut-off mark is 180, but due to the variation of Fine and Applied Arts cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUNAI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUNAI Arts Courses with their Requirements
Education and English and Literary Studies
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Education and English and Literary Studies department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Literature in English plus
three (3) other Arts or Social Science subjects.
Linguistics / English
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Linguistics / English department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Literature in English and
three (3) other relevant subjects.
Christian Religious Studies
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Christian Religious Studies department.
three (3) other relevant subjects.
Igbo
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Igbo department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Islamic Studies
SSCE Requirements
To study this course, candidates seeking admission into the Islamic Studies department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Islamic Studies or Arabic and
any three (3) relevant subjects.
Linguistics
SSCE Requirements
To study this course, candidates seeking admission into the Linguistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any four (4) relevant subjects.
Visual and Applied Arts
SSCE Requirements
To study this course, candidates aspiring to gain admission into Visual and Applied Arts department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
For holders of NTC, the relevant subjects could be
Building / Engineering Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing, Printing Origination;
General Wood work, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Nigerian Universities Offering Fine and Applied Arts Course