If you are planning to study Crop Production and Landscape Management at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Crop Production and Landscape Management?
No, Federal University of Technology Akure does not offer Crop Production and Landscape Management under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Crop Production and Landscape Management course under the Faculty of Agriculture has been updated.
Admission Requirements for Crop Production and Landscape Management When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Crop Production and Landscape Management department under Faculty of Agriculture, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
one Science / Social Science subject and
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Biology / Agriculture and
FUTA Cut-Off Mark for Crop Production and Landscape Management
The general UTME cut-off mark is 180, but due to the variation of Crop Production and Landscape Management cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
Biotechnology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biotechnology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Meteorology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Meteorology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
either Chemistry or Geography.
Forestry and Wood Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Forestry and Wood Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
Software Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Software Engineering department.
two (2) other Science subjects.
Industrial Chemistry
SSCE Requirements
To study this course, candidates seeking admission into the Industrial Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering (AE) department.
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Crop Production and Landscape Management Course