If you are planning to study Microbiology and Biotechnology at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Microbiology and Biotechnology?
No, Federal University of Technology Akure does not offer Microbiology and Biotechnology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Microbiology and Biotechnology course under the Faculty of Science has been updated.
Admission Requirements for Microbiology and Biotechnology When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology and Biotechnology department under Faculty of Science.
FUTA Cut-Off Mark for Microbiology and Biotechnology
The general UTME cut-off mark is 180, but due to the variation of Microbiology and Biotechnology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
Industrial Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
Electrical / Electronics Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Software Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Software Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Remote Sensing and Geosciences Information System
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Remote Sensing and Geosciences Information System department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Joinery,
Floors and Ceiling Finishing, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Human Anatomy
SSCE Requirements
To study this course, candidates seeking admission into the Human Anatomy department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Building
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Microbiology and Biotechnology Course