If you are planning to study Plant Breeding and Seed Science at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Plant Breeding and Seed Science?
No, Federal University of Technology Akure does not offer Plant Breeding and Seed Science under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Plant Breeding and Seed Science course under the Faculty of Agriculture has been updated.
Admission Requirements for Plant Breeding and Seed Science When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Plant Breeding and Seed Science department under Faculty of Agriculture, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
at least O’Level pass in Physics.
JAMB Subject Combination
Mathematics / Physics and
Biology / Agricultural Science.
FUTA Cut-Off Mark for Plant Breeding and Seed Science
The general UTME cut-off mark is 180, but due to the variation of Plant Breeding and Seed Science cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
Building
SSCE Requirements
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Information System
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Information System department.
three (3) other Science subjects.
Animal Production and Health
SSCE Requirements
To study this course, candidates aspiring to gain admission into Animal Production and Health department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science.
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Industrial Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects.
Forestry and Wood Technology
SSCE Requirements
To study this course, candidates seeking admission into the Forestry and Wood Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
Nigerian Tertiary Institutions Offering Plant Breeding and Seed Science Course