If you are planning to study Science Laboratory Technology (SLT) at Federal University of Technology Akure located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTA.
Does Federal University of Technology Akure (FUTA) offer Science Laboratory Technology?
No, Federal University of Technology Akure does not offer Science Laboratory Technology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Akure (FUTA) below to check if the Science Laboratory Technology course under the Faculty of Science has been updated.
Admission Requirements for Science Laboratory Technology (SLT) When Accredited in Federal University of Technology Akure (FUTA)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
JAMB Subject Combination
Any other three (3) relevant subjects (Mathematics, Biology / Agricultural Science, or Physics)
FUTA Cut-Off Mark for Science Laboratory Technology (SLT)
The general UTME cut-off mark is 180, but due to the variation of Science Laboratory Technology (SLT) cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTA Science Courses with their Requirements
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Forestry and Wood Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Forestry and Wood Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
Remote Sensing and Geosciences Information System
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Remote Sensing and Geosciences Information System department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Joinery,
Floors and Ceiling Finishing, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metallurgical and Material Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one other Science subject.
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Nigerian Universities Offering Science Laboratory Technology Course