If you are planning to study Mechatronics and System Engineering at Federal University of Technology Minna located in Niger State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTMINNA.
Does Federal University of Technology Minna (FUTMINNA) offer Mechatronics and System Engineering?
No, Federal University of Technology Minna does not offer Mechatronics and System Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Minna (FUTMINNA) below to check if the Mechatronics and System Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics and System Engineering When Accredited in Federal University of Technology Minna (FUTMINNA)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics and System Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
FUTMINNA Cut-Off Mark for Mechatronics and System Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics and System Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTMINNA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTMINNA Science Courses with their Requirements
Geology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Geology department.
any other relevant subject.
Horticulture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Horticulture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or Agric Science, and
any one other relevant subject.
Crop Production
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Crop Production department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
Botany
SSCE Requirements
To study this course, candidates aspiring to gain admission into Botany department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Mechatronics and System Engineering Course