If you are planning to study Mechatronics Engineering Technology at Federal University of Technology Minna located in Niger State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTMINNA.
Does Federal University of Technology Minna (FUTMINNA) offer Mechatronics Engineering Technology?
No, Federal University of Technology Minna does not offer Mechatronics Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology Minna (FUTMINNA) below to check if the Mechatronics Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering Technology When Accredited in Federal University of Technology Minna (FUTMINNA)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
and any one other subject from:
Biology / Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics / Commerce.
JAMB Subject Combination
Physics / Technical Drawing.
FUTMINNA Cut-Off Mark for Mechatronics Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTMINNA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTMINNA Science Courses with their Requirements
Building
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Education and Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Education and Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology and Agricultural Science.
Chemistry
SSCE Requirements
To study this course, candidates seeking admission into the Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fisheries and Aquaculture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fisheries and Aquaculture department.
Biology/Agricultural Science,
Physics/Geography/Economics.
Agricultural and Bioresources Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural and Bioresources Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Introduction to Agricultural Science, Materials and Workshop Process and Machining, Tractor Layout Power Unit Under Carriage and Auto Electricity; Transmission System; Implement and Machine;
Principles of Crop Husbandry and Land Use, Materials and Workshop Processes; Construction and Maintenance of Agricultural Machines; General Metal Work; General Wood Work and Building / Engineering Drawing.
Metallurgical and Material Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metallurgical and Material Engineering department.
one other Science subject.
Nigerian Tertiary Institutions Offering Mechatronics Engineering Technology Course