
If you are planning to study Horticulture at Federal University of Technology, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTO.
Does Federal University of Technology, Owerri (FUTO) offer Horticulture?
No, Federal University of Technology, Owerri does not offer Horticulture under its Faculty of Renewable and Natural Resources. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology, Owerri (FUTO) below to check if the Horticulture course under the Faculty of Renewable and Natural Resources has been updated.
Admission Requirements for Horticulture When Accredited in Federal University of Technology, Owerri (FUTO)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Horticulture department under Faculty of Renewable and Natural Resources, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or Agric Science, and
any one other relevant subject.
JAMB Subject Combination
Mathematics or Geography.
FUTO Cut-Off Mark for Horticulture
The general UTME cut-off mark is 180, but due to the variation of Horticulture cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTO Science Courses with their Requirements
Biomedical Technology
SSCE Requirements
To study this course, candidates seeking admission into the Biomedical Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Medicine and Surgery
SSCE Requirements
To study this course, candidates seeking admission into the Medicine and Surgery department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Mechatronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Prosthesis and Orthopaedic Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Prosthesis and Orthopaedic Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Nigerian Tertiary Institutions Offering Horticulture Course