If you are planning to study Plant Breeding and Seed Technology at Federal University of Technology, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUTO.
Does Federal University of Technology, Owerri (FUTO) offer Plant Breeding and Seed Tech.?
No, Federal University of Technology, Owerri does not offer Plant Breeding and Seed Tech. under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Federal University of Technology, Owerri (FUTO) below to check if the Plant Breeding and Seed Tech. course under the Faculty of Agriculture has been updated.
Admission Requirements for Plant Breeding and Seed Technology When Accredited in Federal University of Technology, Owerri (FUTO)
O’Level Requirements
To study this course, candidates seeking admission into the Plant Breeding and Seed Technology department under Faculty of Agriculture, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science,
one Science/Social Science subject and
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Biology / Agriculture and
FUTO Cut-Off Mark for Plant Breeding and Seed Technology
The general UTME cut-off mark is 180, but due to the variation of Plant Breeding and Seed Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUTO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUTO Science Courses with their Requirements
Polymer and Textile Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Polymer and Textile Engineering department.
any other Science subject.
Building
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Optometry
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Optometry department.
Physics, Chemistry, Biology and
Additional / Further Mathematics.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Mechatronics Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechatronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Medicine and Surgery
SSCE Requirements
To study this course, candidates seeking admission into the Medicine and Surgery department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Dental Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Dental Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Nigerian Tertiary Institutions Offering Plant Breeding and Seed Tech. Course