If you are planning to study Computer and Communication Engineering at Federal University, Oye-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUOYE.
Does Federal University, Oye-Ekiti (FUOYE) offer Computer and Communication Engineering?
No, Federal University, Oye-Ekiti does not offer Computer and Communication Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Federal University, Oye-Ekiti (FUOYE) below to check if the Computer and Communication Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Computer and Communication Engineering When Accredited in Federal University, Oye-Ekiti (FUOYE)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer and Communication Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
FUOYE Cut-Off Mark for Computer and Communication Engineering
The general UTME cut-off mark is 180, but due to the variation of Computer and Communication Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUOYE Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUOYE Science Courses with their Requirements
Metallurgical and Material Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Metallurgical and Material Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one other Science subject.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Plant Science and Biotechnology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Plant Science and Biotechnology department.
Electrical / Electronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Hospitality and Tourism Management
SSCE Requirements
To study this course, candidates seeking admission into the Hospitality and Tourism Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Animal and Environmental Biology
SSCE Requirements
To study this course, candidates seeking admission into the Animal and Environmental Biology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subject.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Computer and Communication Engineering Course