If you are planning to study Metalwork Technology Education at Federal University, Oye-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUOYE.
Does Federal University, Oye-Ekiti (FUOYE) offer Metalwork Technology Education?
No, Federal University, Oye-Ekiti does not offer Metalwork Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Federal University, Oye-Ekiti (FUOYE) below to check if the Metalwork Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Metalwork Technology Education When Accredited in Federal University, Oye-Ekiti (FUOYE)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metalwork Technology Education department under Faculty of Education, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science, Physics, or Chemistry
and two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
FUOYE Cut-Off Mark for Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUOYE Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUOYE Science Courses with their Requirements
Electrical / Electronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Medical Laboratory Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Medical Laboratory Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Human Kinetics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Human Kinetics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Health Science / Physical Education / Biology
Any other two (2) relevant subjects
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Building
SSCE Requirements
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Hospitality and Tourism Management
SSCE Requirements
To study this course, candidates seeking admission into the Hospitality and Tourism Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Metalwork Technology Education Course