If you are planning to study Software Engineering and Digital Entrepreneurship at Federal University, Oye-Ekiti located in Ekiti State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into FUOYE.
Does Federal University, Oye-Ekiti (FUOYE) offer Software Engineering and Digital Entrepreneurship?
No, Federal University, Oye-Ekiti does not offer Software Engineering and Digital Entrepreneurship under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Federal University, Oye-Ekiti (FUOYE) below to check if the Software Engineering and Digital Entrepreneurship course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Software Engineering and Digital Entrepreneurship When Accredited in Federal University, Oye-Ekiti (FUOYE)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Software Engineering and Digital Entrepreneurship department under Faculty of Data and Decision Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
three (3) other relevant subjects.
JAMB Subject Combination
two (2) other relevant subjects.
FUOYE Cut-Off Mark for Software Engineering and Digital Entrepreneurship
The general UTME cut-off mark is 180, but due to the variation of Software Engineering and Digital Entrepreneurship cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from FUOYE Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other FUOYE Science Courses with their Requirements
Medical Laboratory Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Medical Laboratory Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Microbiology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Plant Science and Biotechnology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Plant Science and Biotechnology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Mechanical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
Food Science and Technology (FT)
SSCE Requirements
To study this course, candidates seeking admission into the Food Science and Technology (FT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Software Engineering and Digital Entrepreneurship Course