If you are planning to study Mechanical Metalwork Technology Education at Gombe State University of Science and Technology located in Gombe State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into GSUTECH.
Does Gombe State University of Science and Technology (GSUTECH) offer Mechanical Metalwork Technology Education?
No, Gombe State University of Science and Technology does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Gombe State University of Science and Technology (GSUTECH) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Gombe State University of Science and Technology (GSUTECH)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology.
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
GSUTECH Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from GSUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other GSUTECH Science Courses with their Requirements
Physics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Physics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
Chemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Software Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Software Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
Information Technology
SSCE Requirements
To study this course, candidates seeking admission into the Information Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course