If you are planning to study Orthopaedic and Plaster Technology at Hassan Usman Katsina Polytechnic located in Katsina State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into HUKPOLY.
Does Hassan Usman Katsina Polytechnic (HUKPOLY) offer Orthopaedic and Plaster Technology?
No, Hassan Usman Katsina Polytechnic does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Hassan Usman Katsina Polytechnic (HUKPOLY) below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Hassan Usman Katsina Polytechnic (HUKPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
HUKPOLY Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from HUKPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other HUKPOLY Science Courses with their Requirements
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nutrition and Dietetics
SSCE Requirements
To study this course, candidates seeking admission into the Nutrition and Dietetics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science.
Animal Health and Production Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Animal Health and Production Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three (3) of the following:
Geography, Food and Nutrition, Economics, Technical Drawing,
English Language, Physics, Chemistry, Nigerian Language, and Home Economics.
Statistics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Statistics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other relevant subject.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Welding and Fabrication Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course