If you are planning to study Human Kinetics and Health Education at Hussaini Adamu Federal Polytechnic located in Jigawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into HAFEDPOLY.
Does Hussaini Adamu Federal Polytechnic (HAFEDPOLY) offer Human Kinetics and Health Education?
No, Hussaini Adamu Federal Polytechnic does not offer Human Kinetics and Health Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Hussaini Adamu Federal Polytechnic (HAFEDPOLY) below to check if the Human Kinetics and Health Education course under the Faculty of Education has been updated.
Admission Requirements for Human Kinetics and Health Education When Accredited in Hussaini Adamu Federal Polytechnic (HAFEDPOLY)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Human Kinetics and Health Education department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any three (3) other relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
HAFEDPOLY Cut-Off Mark for Human Kinetics and Health Education
The general UTME cut-off mark is 230, but due to the variation of Human Kinetics and Health Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from HAFEDPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other HAFEDPOLY Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Printing Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Printing Technology department.
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Mechanical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Estate Management and Valuation
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Estate Management and Valuation department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Polymer Technology
SSCE Requirements
To study this course, candidates seeking admission into the Polymer Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Nigerian Tertiary Institutions Offering Human Kinetics and Health Education Course