If you are planning to study Glass Technology at Imo State University, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMSU.
Does Imo State University, Owerri (IMSU) offer Glass Technology?
No, Imo State University, Owerri does not offer Glass Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Imo State University, Owerri (IMSU) below to check if the Glass Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Glass Technology When Accredited in Imo State University, Owerri (IMSU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Glass Technology department under Faculty of Engineering / Technology.
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
IMSU Cut-Off Mark for Glass Technology
The general UTME cut-off mark is 180, but due to the variation of Glass Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMSU Science Courses with their Requirements
Civil Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Electrical / Electronics Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Industrial Physics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Physics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Forestry and Wildlife
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forestry and Wildlife department.
Further Mathematics and Statistics.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering (AE) department.
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Glass Technology Course