If you are planning to study Mechatronics Engineering at Imo State University, Owerri located in Imo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMSU.
Does Imo State University, Owerri (IMSU) offer Mechatronics Engineering?
No, Imo State University, Owerri does not offer Mechatronics Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Imo State University, Owerri (IMSU) below to check if the Mechatronics Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechatronics Engineering When Accredited in Imo State University, Owerri (IMSU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechatronics Engineering department under Faculty of Engineering / Technology.
any other Science subject.
IMSU Cut-Off Mark for Mechatronics Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechatronics Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMSU Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Building
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Industrial Physics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Physics department.
any other Science subject from Further Mathematics and Biology or Agricultural Science.
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Crop Science and Biotechnology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Crop Science and Biotechnology department.
Biology or Agricultural Science and
any other relevant subject.
Nigerian Universities Offering Mechatronics Engineering Course