If you are planning to study Geological Technology at Institute of Management Technology, Enugu located in Enugu State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into IMT.
Does Institute of Management Technology, Enugu (IMT) offer Geological Technology?
No, Institute of Management Technology, Enugu does not offer Geological Technology under its Faculty of Earth and Mineral Sciences. However, since our course list is updated regularly, you can visit the courses available at Institute of Management Technology, Enugu (IMT) below to check if the Geological Technology course under the Faculty of Earth and Mineral Sciences has been updated.
Admission Requirements for Geological Technology When Accredited in Institute of Management Technology, Enugu (IMT)
O’Level Requirements
To study this course, candidates seeking admission into the Geological Technology department under Faculty of Earth and Mineral Sciences, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) subjects from:
IMT Cut-Off Mark for Geological Technology
The general UTME cut-off mark is 180, but due to the variation of Geological Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from IMT Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other IMT Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Food Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Technology department.
Biology / Agricultural Science,
any two of the following:
Geography, Food and Nutrition, Economics, Technical Drawing, Physics, Chemistry, Nigerian Language and Home Economics.
At least a pass in Chemistry is required.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Glass / Ceramics Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Glass / Ceramics Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Civil Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Civil Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Printing Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Printing Technology department.
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Nigerian Tertiary Institutions Offering Geological Technology Course