If you are planning to study Marine Engineering Technology at Kaduna Polytechnic located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Kaduna Polytechnic.
Does Kaduna Polytechnic (KADPOLY) offer Marine Engineering Technology?
No, Kaduna Polytechnic does not offer Marine Engineering Technology under its Faculty of Maritime Studies. However, since our course list is updated regularly, you can visit the courses available at Kaduna Polytechnic (KADPOLY) below to check if the Marine Engineering Technology course under the Faculty of Maritime Studies has been updated.
Admission Requirements for Marine Engineering Technology When Accredited in Kaduna Polytechnic (KADPOLY)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Marine Engineering Technology department under Faculty of Maritime Studies.
any one (1) other subject from:
Biology / Agricultural Science, Technical Drawing, Auto Mechanics,
Basic Electronics / Basic Electricity,
Metal Work, Woodwork for Civil Engineering Technology,
Further Mathematics, English Language, Geography, Economics / Commerce.
JAMB Subject Combination
Physics or Technical Drawing.
Kaduna Polytechnic Cut-Off Mark for Marine Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Marine Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Kaduna Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Kaduna Polytechnic Science Courses with their Requirements
Mineral and Petroleum Resources Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mineral and Petroleum Resources Engineering Technology department.
Woodwork for Civil Engineering Technology, Further Mathematics, English Language, Geography, Economics/Commerce,
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work.
Chemical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, Geography and Economics / Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Civil Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Civil Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Surveying and Geoinformatics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Marine Engineering Technology Course